Micetek, le spécialiste des outils de développement pour PowerPC/ARM

Micetek est la société Taïwanaise qui a succédé à MicroTek en 1998 dans la fourniture d'outils de développement pour les systèmes embarqués.

MiceTek propose des cartes d'évaluation et de développement basées sur les processeurs PowerQUICC de Freescale.

MPC8313E-RDB Carte de référence économique

· CPU: Freescale MPC8313E running at 333/133 MHz (CPU/CSB (Coherent System Bus))
· Memory subsystem:
— 128 MByte unbuffered DDR2 SDRAM discrete devices
— 8 MByte Flash single-chip memory
— 32 MByte NAND Flash memory
— 256 KBit M24256 serial EEPROM
— SD connector to interface with the SD memory card in SPI mode
· Interfaces:
— 10/100/1000 BaseT Ethernet ports:
– eTSEC1, RGMII interface: five 10/100/1000 BaseT RJ-45 interfaces using
   Vitesse™ VSC7385 L2 switch
– eTSEC2, selectable RGMII or SGMII interface: one 10/100/1000 BaseT
    RJ-45 interface using Mavell™ 88E1111 PHY
— USB 2.0 port:
– High speed host/device USB interface: selectable on-chip PHY or external
   ULPI PHY interface by SMSC USB3300 USB PHY
— PCI: 32-bit PCI interface running at up to 66 MHz
– One 32-bit 3.3 V PCI slot connected to PCI bus
– One 32-bit 3.3 V miniPCI slot connected to PCI bus
— Dual UART ports:
– DUART interface: supports two UART up to 115200bps for console display
· Board connectors:
— LCD connectors by GPIO
— ATX power supply connector
— JTAG/COP for debugging

· IEEE1588 signals for test and measurement
· Real time clock and thermal sensor on I2C bus
· Programmable LEDs for debug use
· Mini-ITX form factor: 170 mm × 170 mm, excluding chassis
· 6-layer PCB routing (4-layer signals, 2-layer power and ground)
Software:
· U-Boot
· Linux kernel
. Ramdisk server
· Tool chain : gcc et binutils

MPC8323E-RDB Carte de référence

· CPU: Freescale MPC8323E running at 333/133 MHz (CPU/CSB (Coherent System Bus))
· Memory subsystem:
      — 64 MByte unbuffered DDR2 SDRAM discrete devices
      — 16 MByte Flash single-chip memory
      — 256 MBits M24256 serial EEPROM
      — SD connector to interface with the SD memory card in SPI mode
· Interfaces:
      — 10/100 BaseT Ethernet ports:
              – UCC2, MII interface: four 10/100 BaseT RJ-45 interface using
                 ICPlus™ IP175C L2 switch
              – UCC3, MII interface: one 10/100 BaseT RJ-45 interface using the
                independent PHY of the same ICPlus™ IP175C L2 switch
      — Phone ports:
              – SPI and TDM interface: two RJ-11 phone port using Legerity™
                 Le88221 SLIC Codec
      — USB 2.0 host ports:
              – USB1 and USB2, PCI interface: two USB2.0 type A receptacle
                 connectors, with NEC™ μPD720102 USB 2.0 host controller
      — PCI: 32-bit PCI interface running at up to 66 MHz
              – One 32-bit 3.3 V PCI slot (or optional mini-PCI slot on bottom side) connected to PCI bus
              – One 32-bit 3.3 V mini-PCI slot connected to PCI bus

· Board connectors:
      — Expansion connectors:
              – Two expansion connectors with UTOPIA Level 2 in 8-bit master mode interface and MII/RMII interface
                 for external xDSL module
              – One optional DSP connector with 5-bit load bus addressing and 8-bit data bus for external DSP or local
               bus module
      — +12 V and +5 V power supply 4P connector for using chassis power or ATX power supply
      — +12 V and +5 V power supply DIN connector for using power adapter
      — RS-232C connectors
              – 1x 9 pin DB9 receptacle or 1x10 pin 2.54 mm connector
      — UART connector
              – 1x 6 pin UART connector with 3.3 V power
      — JTAG/COP for debugging
      — Form factor: 152.4 mm × 146.1 mm, or 6000 mils × 5750 mils, excluding chassis
Software:
· U-Boot
· Linux kernel
. Ramdisk server
· Tool chain : gcc et binutils

	© NeoMore
Mentions légales Accueil - Société - Temps Réel - Analyse de Bus - Cartes Industrielles - Systèmes - Services - Partenaires - Boutique